Ghost 2 Immobiliser Reviews
The Ghost 2 immobiliser utilizes cutting-edge technology to prevent car theft. This hidden device is not noticed by thieves and only turns on the engine after a PIN or app is entered.
It connects to the CAN data network of your vehicle and is weatherproof. It also comes with a service/valet mode, which allows you to start your car for a short period while it's in garage for cleaning or servicing.
Easy to install
The Ghost immobiliser guards your vehicle from theft of keys as well as hacking, cloning and stealing. It uses an PIN code system that is integrated into your car's electronic control unit, making it difficult for thieves to recognize. Unlike traditional immobilisers, it doesn't require special keys or sensors, and is completely hidden from view without any LED indicators or signals that signal its presence. It's also less expensive than replacing an ECU or installing a new key fob and could lower the cost of your monthly insurance.
Follow the directions of the manufacturer when installing follow the manufacturer's instructions when installing a Ghost 2 vehicle immobiliser. This will ensure the device works correctly and effectively. After the installation is completed Test the system by entering the PIN code, then turning on the engine. Regular testing will help you spot any problems before they get worse.
Before you begin the installation, make sure you check the position of the CAN H and L wires. These are crucial to powering the immobiliser, so it is important that they are properly connected. It is also a good idea to label the wires to make it easier to identify them when installing the device. Once you have identified the locations of these wires and connected them to a constant 12V power source as well as an earthing point. Use the fuse tap to safeguard the connections against damage or short-circuits.
After connecting the wires, neaten the wiring using cable ties to avoid potential interference. It is also a good idea to cover the connections with insulation tape or heat shrink tubing. This will protect the device from electrical shorts, and prolong its life. Once the wiring is secured, it's a good idea test the Ghost 2 immobiliser.
The Ghost 2 immobiliser offers a service mode in situations where you may have to surrender your vehicle, such as when it is being serviced or valet parked. This will disable the PIN sequence temporarily. To activate this feature, simply press the brake pedal while holding down the accelerator, and press a number of times equal to the first digit of the emergency code. The system will then go into service mode, which is verified by flashing the indication signal 5 times.
Easy to change PIN codes
It is simple to secure your vehicle from theft by installing a ghost 2 immobiliser. It is concealed within the vehicle, and is only accessible through a specific code. The device communicates with the vehicle ECU via its data bus and does not rely on radio frequency signals as alarm systems that are sold on the market or traditional Thatcham immobilisers do. This makes it harder for thieves to hear the click of an immobiliser relay or to add new keys. The control unit is concealed within the wiring harness or dashboard, and cannot be physically tampered with to reset the system.
The ghost 2 immobiliser is connected to your vehicles CAN Data network and makes use of the buttons already present on the steering wheel, door panels and the centre console to create an individual sequence of up 20 button presses. ghost ii immobiliser must be entered before the engine can begin similar to the PIN code. This next-generation system does not require wire cutting upon installation and can be reprogrammed at any time. You can even start your vehicle in Service or Valet mode after you hand it to a mechanic to perform work.
The application can also be used to disable your PIN code in the event that you've lost your keys, or change it. This feature is especially helpful if you have given your car to a third party to be used as a valet or service, as it stops them from starting your car and taking it away without consent. It's also inaccessible to professional thieves, as it doesn't make use of radio frequencies or circuit cuts.
The ability of the immobiliser to prevent relay thefts is another excellent feature. Relay theft is a typical method of car theft where thieves hack into the diagnostic port on your car and alter the signal that is sent by the key to the vehicle's ECU to trick it into thinking that the key is valid. This is the way traditional immobilisers are removed, however with a ghost 2 immobiliser, the signal is blocked before it can reach the ECU.
Easy to use app
Ghost 2 is a revolutionary immobiliser that shields your vehicle from hacking, key-cloning and key theft. It connects to the CAN data network of your vehicle and requires a PIN code in order to start the engine. It also stops thieves from by using signal spoofing or device spoofing, which are both common methods of stealing vehicles.
The system is simple to use and works just similar to a standard car alarm. After installing it, you can create a unique PIN code sequence that can be up to 20 digits in length and must be entered before the vehicle starts. This will prevent the vehicle from being stolen, even the case that you lose your keys. You can disable the system using an app for your smartphone.
Contrary to other systems that are silent, the ghost is quiet and doesn't emit any radio frequency signals. It is a weatherproof and discreet device that can be installed anywhere in your vehicle. It can be easily hidden under the dash, the steering wheel, or on the door panels. It communicates with your ECU through the CAN data circuit, and is not affected by diagnostic tools, which some thieves use to find security systems. It is also not affected by jamming devices that alter codes.
It is a covert system that can be used to deter the theft of all vehicles. Its technology has been proven efficient, and it's in compliance with TASSA Standards. The Ghost is a good choice for classic, sports, and prestige cars. It can also be used as a way to protect vehicles being rental on apps such as Turo.
The Autowatch Ghost 2 is the next generation of car immobilisers. This system is invisible to thieves, and prevents them from starting your car without your PIN, or unless they have been authorized by the app. It also doesn't emit radio frequencies or other signals that could be detected by scanners. Installation is fast and simple. The app has an easy-to-use interface and simple navigation. It also comes with a GPS tracker that can help police locate and locate the vehicle.
Easy to reset
A ghost 2 immobiliser is a great way to protect your vehicle from theft. It integrates into your vehicle's ECU and creates a security barrier that thieves are unable to breach without the correct pin. It's also TASSA-certified which means it's recognized by insurance companies. It's an effective tool for preventing car theft, and can save you a lot of dollars in the long run.
The Ghost system unlike traditional alarms and immobilisers that require cutting of circuits and is directly connected to the vehicle's CAN data network. It works by pressing the buttons on your dashboard and the steering wheel. You can create an individual PIN sequence, which can be up to 20 presses in length. This PIN must be entered before your engine can begin the engine, just like the PIN you use on your credit card. Ghost is unnoticeable to thieves, and there are no indicators that signal its presence, which makes it the most effective aftermarket CAN bus immobiliser that is on the market today.
Another advantage of the Ghost system is that it doesn't utilize radio frequency signals, meaning it cannot be detected or scanned by thieves. This prevents cloned key attacks and relay attacks as and the typical method of hacking into the computer system of a car using its CAN bus scanning for signals. The Ghost system is designed so that it can be hidden within your vehicle. There aren't any LEDs, or other signals to show its presence.
The system features the option of a Transport Mode which disables the Ghost System. This is beneficial for situations when you need to temporarily deactivate Ghost, such as when you're transporting or maintaining your vehicle. This mode is less effective than Service Mode as it doesn't disable the Ghost system when you exceed 31 mph within 15 minutes.
To reset your ghost 2 immobiliser you'll need the emergency code, which you can obtain from your installer. It is typically hidden under a scratch-off area on the card provided with the installation. You should keep this emergency code safe and keep it in a place that is secure, such as your wallet at home.